- Brand: SARA®
- Article no.: 1045050055
- Catalogue page: KS-0215
- Cutting values: SW-0384
Product description
104505 Boring bar SARADRILL for boring headSARADRILL solid drilling tool- Machining of bore holes from Ø 49 to 270 mm
- For machines with low drive power
- Low-vibration, equipment-friendly machining with up to 50 % less drive power
- Drilling in a single operation without centring and pre-drilling
- No front face planing required
- Cost-efficient boring system, since differences in diameter of up to 30 mm can be machined with one boring head by changing the cutting edges
- Variable drilling depths of up to 15 x D due to holding fixture system with pluggable extensions
- Internal coolant supply directly to the cutting edge, no high-pressure pump required
- For rotating tools, the coolant is supplied via a coolant ring
- Short chips due to chip-separating grooves in the roughing blade, no chip removal, even with extremely deep bores
- Also for use on vertically operating machines
- Low tool costs as wear is limited to the cutting edges and centre bit
- Unproblematic regrinding of the centre bit and the cutting edges (in pairs) using the grinding fixture or the tool grinding machine
- Cutting material:
Cutting edge HSS-E-PM ASP30, ASP30 TiN
HSS centre bit - For use on all machine tools as a rotating or stationary tool especially for machining large bore diameters on machines with low drive power
- Caution: Not suitable for boring out existing holes!
Boring bar with Morse taper shank
- Brand: SARA®
- Article no.: 1045100055
- Catalogue page: KS-0216
- Cutting values: SW-0384
Product description
104510 Extension 150 mm SARADRILL for boring headSARADRILL solid drilling tool- Machining of bore holes from Ø 49 to 270 mm
- For machines with low drive power
- Low-vibration, equipment-friendly machining with up to 50 % less drive power
- Drilling in a single operation without centring and pre-drilling
- No front face planing required
- Cost-efficient boring system, since differences in diameter of up to 30 mm can be machined with one boring head by changing the cutting edges
- Variable drilling depths of up to 15 x D due to holding fixture system with pluggable extensions
- Internal coolant supply directly to the cutting edge, no high-pressure pump required
- For rotating tools, the coolant is supplied via a coolant ring
- Short chips due to chip-separating grooves in the roughing blade, no chip removal, even with extremely deep bores
- Also for use on vertically operating machines
- Low tool costs as wear is limited to the cutting edges and centre bit
- Unproblematic regrinding of the centre bit and the cutting edges (in pairs) using the grinding fixture or the tool grinding machine
- Cutting material:
Cutting edge HSS-E-PM ASP30, ASP30 TiN
HSS centre bit - For use on all machine tools as a rotating or stationary tool especially for machining large bore diameters on machines with low drive power
- Caution: Not suitable for boring out existing holes!
Extension
- Brand: SARA®
- Article no.: 1045150055
- Catalogue page: KS-0216
- Cutting values: SW-0384
Product description
104515 Extension 300 mm SARADRILL for boring headSARADRILL solid drilling tool- Machining of bore holes from Ø 49 to 270 mm
- For machines with low drive power
- Low-vibration, equipment-friendly machining with up to 50 % less drive power
- Drilling in a single operation without centring and pre-drilling
- No front face planing required
- Cost-efficient boring system, since differences in diameter of up to 30 mm can be machined with one boring head by changing the cutting edges
- Variable drilling depths of up to 15 x D due to holding fixture system with pluggable extensions
- Internal coolant supply directly to the cutting edge, no high-pressure pump required
- For rotating tools, the coolant is supplied via a coolant ring
- Short chips due to chip-separating grooves in the roughing blade, no chip removal, even with extremely deep bores
- Also for use on vertically operating machines
- Low tool costs as wear is limited to the cutting edges and centre bit
- Unproblematic regrinding of the centre bit and the cutting edges (in pairs) using the grinding fixture or the tool grinding machine
- Cutting material:
Cutting edge HSS-E-PM ASP30, ASP30 TiN
HSS centre bit - For use on all machine tools as a rotating or stationary tool especially for machining large bore diameters on machines with low drive power
- Caution: Not suitable for boring out existing holes!
Extension
- Brand: SARA®
- Article no.: 1045200070
- Catalogue page: KS-0216
- Cutting values: SW-0384
Product description
104520 Carbide guide SARADRILL for boring headSARADRILL solid drilling tool- Machining of bore holes from Ø 49 to 270 mm
- For machines with low drive power
- Low-vibration, equipment-friendly machining with up to 50 % less drive power
- Drilling in a single operation without centring and pre-drilling
- No front face planing required
- Cost-efficient boring system, since differences in diameter of up to 30 mm can be machined with one boring head by changing the cutting edges
- Variable drilling depths of up to 15 x D due to holding fixture system with pluggable extensions
- Internal coolant supply directly to the cutting edge, no high-pressure pump required
- For rotating tools, the coolant is supplied via a coolant ring
- Short chips due to chip-separating grooves in the roughing blade, no chip removal, even with extremely deep bores
- Also for use on vertically operating machines
- Low tool costs as wear is limited to the cutting edges and centre bit
- Unproblematic regrinding of the centre bit and the cutting edges (in pairs) using the grinding fixture or the tool grinding machine
- Cutting material:
Cutting edge HSS-E-PM ASP30, ASP30 TiN
HSS centre bit - For use on all machine tools as a rotating or stationary tool especially for machining large bore diameters on machines with low drive power
- Caution: Not suitable for boring out existing holes!
Carbide guide- For use with extremely deep bores
- Brand: SARA®
- Article no.: 1045400001
- Catalogue page: KS-0216
- Cutting values: SW-0384
Product description
104540 Coolant ring SARADRILL for boring headSARADRILL solid drilling tool- Machining of bore holes from Ø 49 to 270 mm
- For machines with low drive power
- Low-vibration, equipment-friendly machining with up to 50 % less drive power
- Drilling in a single operation without centring and pre-drilling
- No front face planing required
- Cost-efficient boring system, since differences in diameter of up to 30 mm can be machined with one boring head by changing the cutting edges
- Variable drilling depths of up to 15 x D due to holding fixture system with pluggable extensions
- Internal coolant supply directly to the cutting edge, no high-pressure pump required
- For rotating tools, the coolant is supplied via a coolant ring
- Short chips due to chip-separating grooves in the roughing blade, no chip removal, even with extremely deep bores
- Also for use on vertically operating machines
- Low tool costs as wear is limited to the cutting edges and centre bit
- Unproblematic regrinding of the centre bit and the cutting edges (in pairs) using the grinding fixture or the tool grinding machine
- Cutting material:
Cutting edge HSS-E-PM ASP30, ASP30 TiN
HSS centre bit - For use on all machine tools as a rotating or stationary tool especially for machining large bore diameters on machines with low drive power
- Caution: Not suitable for boring out existing holes!
Coolant ring- Compl. with coupling, grip bar and circlips
- Brand: SARA®
- Article no.: 1045700001
- Catalogue page: KS-0216
- Cutting values: SW-0384
Product description
104570 Replacement shim SARADRILL for boring headSARADRILL solid drilling tool- Machining of bore holes from Ø 49 to 270 mm
- For machines with low drive power
- Low-vibration, equipment-friendly machining with up to 50 % less drive power
- Drilling in a single operation without centring and pre-drilling
- No front face planing required
- Cost-efficient boring system, since differences in diameter of up to 30 mm can be machined with one boring head by changing the cutting edges
- Variable drilling depths of up to 15 x D due to holding fixture system with pluggable extensions
- Internal coolant supply directly to the cutting edge, no high-pressure pump required
- For rotating tools, the coolant is supplied via a coolant ring
- Short chips due to chip-separating grooves in the roughing blade, no chip removal, even with extremely deep bores
- Also for use on vertically operating machines
- Low tool costs as wear is limited to the cutting edges and centre bit
- Unproblematic regrinding of the centre bit and the cutting edges (in pairs) using the grinding fixture or the tool grinding machine
- Cutting material:
Cutting edge HSS-E-PM ASP30, ASP30 TiN
HSS centre bit - For use on all machine tools as a rotating or stationary tool especially for machining large bore diameters on machines with low drive power
- Caution: Not suitable for boring out existing holes!
Replacement clamps- For boring heads (prices per set of 2 heads)
Shopping cart contains offer
The shopping cart currently contains articles from offer and cannot contain any further articles.
Do you want to empty the shopping cart and add this article?